- 您现在的位置：买卖IC网 > Sheet目录629 > P1641100 (Red Lion Controls)P16 ANALOG CONTROLLER
3.0 W IRING
THE
C ONTROLLER
WIRING CONNECTIONS
All wiring connections are made to the rear screw terminals. When wiring the
controller, use the numbers on the label and those embossed on the back of the
case, to identify the position number with the proper function.
All conductors should meet voltage and current ratings for each terminal.
Also, cabling should conform to appropriate standards of good installation, local
codes and regulations. It is recommended that power (AC or DC) supplied to the
controller be protected by a fuse or circuit breaker. Strip the wire, leaving
approximately 1/4" (6 mm) bare wire exposed (stranded wires should be tinned
with solder). Insert the wire under the clamping washer and tighten the screw
until the wire is clamped tightly.
CONTROLLER POWER CONNECTIONS
For best results, the power should be relatively “clean” and within
the specified limits. Drawing power from heavily loaded circuits or
from circuits that also power loads that cycle on and off should be
avoided. It is recommended that power supplied to the controller be
protected by a fuse or circuit breaker.
DC+
11
VDC
DC-
12
~
AC
11
VAC
~
AC
12
+
-
INPUT CONNECTIONS
For two wire RTDs, install a copper sense lead of the same gauge and length
as the RTD leads. Attach one end of the wire at the probe and the other end to
input common terminal. Complete lead wire compensation is obtained. This is
the preferred method. If a sense wire is not used, then use a jumper. A
temperature offset error will exist. The error may be compensated by
programming a temperature offset.
RTD and Resistance
Thermocouple and Millivolt
Voltage and Current
COMM 8
COMM 8
TC-
COMM 8
DC-
TC+
RTD
9
10
TC+
RTD
9
10
TC+
10V
20mA
9
10
DC+ VOLTAGE
DC+ CURRENT
CONTROL AND ALARM OUTPUT CONNECTIONS
Alarm Models
Main Control Relay Models
AC/DC
POWER
LOAD
2
3
N.O.
COMM.
A1/O1*
(+) O1
(-) O1
6
7
LOAD
AC/DC
POWER
SSR
-
AC
7
AC/DC
POWER
LOAD 4 N.O.
5 COMM.
* A1 becomes main control O1, if selected for
heating in the analog out models.
A2/O2
(+) O1
(-) O1
Main Control Logic/SSR Models
6 + AC
POWER AC POWER
UNIT
ANALOG DC OUTPUT CONNECTIONS
USER INPUT CONNECTIONS
INPUT 1
+V/I
- V/I
6
7
CONTROLLER,
RECORDER
USER
8
COMM.
6
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
P1Z9ACR900W12
DIODE MOD PWR-BRIK DL 1200V 740A
PA3716
TOOL REPLACEMENT HEAD SET
PAXCDL10
ANALOG OUTPUT CARD
PAXLC800
COUNTER 8-DIGIT BI-DIR COUNT
PAXLPT00
METER PROCESS TIME 6-DIGIT
PAXLR000
METER RATE INDICATION 6-DIGIT
PB52233SLK
PROJ BOARD COLDFIRE M52
PD412411
DIODE MOD ISO DUAL 2400V 1100A
相关代理商/技术参数
P1641110
制造商:Red Lion Controls 功能描述:PROCESS CONTR, 1/16DIN DC ANALOG 2 ALRM 制造商:Red Lion Controls 功能描述:DC W/ANALOG OUT 2 ALARMS
P1-64121
制造商:OTTO 功能描述:Pushbutton Switches Style F Scrw LoLev Red Button 制造商:OTTO Engineering Inc 功能描述:Switch Push Button N.O. Round Button 10A 115VAC 28VDC Momentary Contact Screw Panel Mount
P1-64122
功能描述:按钮开关 Style F Scrw LoLev Black Button
RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级:
P1-64122W
制造商:OTTO 功能描述:Pushbutton Switches Style F Scrw LoLev Black Button 制造商:OTTO Engineering Inc 功能描述:STYLE F,SCREW,LOW
P1-64128
功能描述:按钮开关 Style F Scrw LoLev Gray Button
RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级:
P1-64129
功能描述:按钮开关 Style F Scrw LoLev White Button
RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级:
P1-64131
制造商:OTTO Engineering Inc 功能描述:Switch Push Button N.O. Round Button 10A 115VAC 28VDC Screw Panel Mount
P1-64132
制造商:OTTO Engineering Inc 功能描述:Switch Push Button N.O. Round Button 10A 115VAC 28VDC Screw Panel Mount